自动注塑挤出中央供料系统

自动注塑挤出中央供料系统集中送料系统具有以下特点： 

一、完善服务：完善的售后服务，工程师亲自到厂保养维修，让您完全无后顾之忧。 运转状态LED显示面板： 依机台陈列方式设计，明白指示机台位

置，无论是监控动自动注塑挤出中央供料系统采用真空传送方式，通过集中的管路系统将塑料原料从储料罐输送到中央除湿干燥系统，然后将干燥后的原

料输送到每台注塑机中。

1、达安泰公司内部高效高技能的施工队伍，确保施工进度及整体工程与原有注塑车间的无暇衔接

2.由专业工程师为您施工、安装、到测试完成后交机，一系列的专业服务，并提供必要的教育训练及技术指导。

3.提供您*高品质、高价值的产品。我们的产品一应俱全，从除湿干燥机到自动计量混料机、料斗干燥机、全自动真空式填料机、冷冻机等，应有尽有。

品质***得您信赖。

4.从厂房规划、水电工程设计、无尘室工程设计、技术咨询、到整厂流程规划，由专人为您提供*完整、*专业的设计规划。

二、节能：由于采用了中央供料的方式、相对应地减少了很多的单机设备，也就节省了电能及减少维护费用。自动注塑挤出中央供料系统操作简易，只需

要少数的几个人即可以控制整个注塑工厂的供料需求，从而减少了大量的劳动力成本。其次、减少了在注塑机旁边的原料带及相应的辅助设备、提高了空

间的利用率。

三、个性化：达安泰自动注塑挤出中央供料系统独特集中粉尘回收系统，清理更便捷、环保效果更是达到10万级无尘室作业要求标准，并降低噪音，*终

可实现无人化的自动化生产车间，树立起现代化工厂管理的形象。自动注塑挤出中央供料系统可以做到不同的使用用户，不同的车间特点，不同的原料使

用要求。都可以依实际的需要来设计出*优化的方案。

四、现代化工厂形象：自动注塑挤出中央供料系统将使原料及粉尘对注塑生产的污染减至*底的程度，从而可以保持洁净的生产车间，

五、高效：能够实行高度的自动化控制、监测等、并能满足24小时不停机的生产需要自动注塑挤出中央供料系统可实现将多种原料自动供给多室任意的注

塑加工设备使用，在这其中可包括原料的干燥处理、配色处理、以及按比例的粉碎回收料利用，。 

达安泰公司自动注塑挤出中央供料系统采用“一台机器一根管”的设计方式，保证整个系统的空气对原料进行输送，防止除湿干燥后的原料回潮。同时在每

个输运行稳定，绝无堵料的现象发生。它配合中央除湿干燥系统使用，可使用除湿干燥送循环后会对输送管线进行清理，确保管路内没有残余的粒料，在

避免原料回潮的同时，也保证了加入注塑机中的原料性能的一致。在真空负压作用下原料中原由的粉尘会通过粉尘过滤系统被过滤出来，有助于提高成型

产品的质量。

(供料系统,中央供料系统,大型除湿系统，混色系统，拌料，自动开包卸料站)

以上是中央供料系统的介绍，欢迎新老客户朋友前来定制自动挤出中央供料系统

Automatic Injection Molding The central feed system uses vacuum transport to transport the plastic material from the storage tank to the central dehumidification drying system through a centralized piping system and then transport the dried raw material to each injection molding machine.

D'Aantai automatic injection molding out of the central feeding system using "a machine a tube" design, to ensure that the entire system of air to transport raw materials to prevent dehumidification after drying raw materials resurgence. At the same time in each transport line is stable, no blocking material phenomenon occurred. It is used with the central dehumidification drying system,

You can use the dehumidification drying cycle will be sent to clean the pipeline to ensure that there is no residual pellet in the pipeline,

In order to avoid the return of raw materials at the same time, but also to ensure that the injection molding machine to join the performance of raw materials consistent. In the vacuum under the action of raw materials in the original dust will be filtered through the dust filter system, help to improve the quality of molding products.

Automatic Injection Molding Central Feeding System The centralized feeding system has the following characteristics:
First, the efficient: automatic injection molding Central feeding system can be achieved by a variety of raw materials automatically supply multi-chamber arbitrary injection molding equipment used, which may include raw materials, drying, color processing,

As well as the proportion of the use of crushed recycled materials, to carry out a high degree of automation control, monitoring, etc., and to meet the 24-hour non-stop production needs.
 
Second, energy saving: automatic injection molding Central feeding system is easy to operate, only a few people can control the injection of the entire plant demand for the plant, thereby reducing the large number of labor costs. Second, the reduction in the injection molding machine next to the raw material and the corresponding auxiliary equipment, improve the utilization of space.

In addition, due to the use of the central way of supply, corresponding to reduce a lot of stand-alone equipment, also saves energy and reduce maintenance costs.
Third, the individual: automatic injection molding Central feeding system can be done using different users, different workshop characteristics, different requirements for the use of raw materials. Can be designed according to the actual needs of the optimal solution.


Fourth, the modern factory image: automatic injection molding out of the central feeding system will make raw materials and dust on the injection molding production to minimize the level of pollution, which can maintain a clean production workshop, and Da Aetai automatic injection extrusion central feeding system Unique concentration of dust recovery system, clean more convenient, environmental protection effect is to reach 100,000 clean room operating requirements standards, and reduce noise, and ultimately can achieve unmanned automated production workshop, and establish a modern factory management image.
Fifth, improve the service: Da Aetai company within the highly efficient and highly skilled construction team to ensure that the construction schedule and the overall project and the original injection workshop
1, from the plant planning, hydropower engineering design, clean room engineering design, technical advice, to the whole plant process planning, by the

People to provide you with the most complete and most professional design and planning.
2. To provide you with the highest quality, high value of the product. Our products are readily available, from dehumidification dryer to automatic metering mixer, hopper dryer, automatic vacuum filling machine, freezer, everything. Quality is definitely worth your trust.
3. By professional engineers for your construction, installation, to complete the test after the delivery, a series of professional services, and provide the necessary education and training and technical guidance.
4. Perfect after-sales service, engineers personally to the factory maintenance, so you completely worry-free. Operating status LED display panel: according to the machine display design, understand the location of the machine, whether it is monitoring


(Feeding system, central feeding system, large dehumidification system, color mixing system, spices, automatic unpacking station)
Above is the introduction of the central feeding system, welcomed the new and old customers to come to custom custom injection extrusion center feeding system