产品中心
PRODUCT CENTER
- 联系人 : 曹镜森先生
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 移动电话 : 15989458768
- 地址 : ** 广东省东莞市大朗镇仙村仙一区99号
- Email : caojingshen@126.com
- 邮编 : 523792
- 公司网址 : //m.zhuguangze.com
- MSN : caoshingcer@126.com
- QQ : 454992321
- 联系人 : 曹镜森
- 联系电话 : 0769-82226193
- 传真 : 0769-82226193
- 公司网址 : //m.zhuguangze.com/
产品详情
简单介绍:
自动加料系统说明书
I.启动前的准备工作
1.检查送料器的气源压力是否正常(0.5-0.6 MPa)以及电源是否打开; 2,检查管件是否正确连接; 3,检查各种材料是否准备好;
II。自动加料系统说明书系统操作
详情介绍:
自动加料系统说明书
I.启动前的准备工作
1.检查送料器的气源压力是否正常(0.5-0.6 MPa)以及电源是否打开; 2,检查管件是否正确连接; 3,检查各种材料是否准备好;
II。自动加料系统说明书系统操作
1.打开控制柜中的主电源开关,将控制面板上的电源旋钮开关转到“开”位置,电源指示灯亮;
2.在触摸屏下校准和清,除两个称重系统监视器的值;
3.当触摸屏操作进入功能选择屏幕时,可以根据工艺要求进入“参数设置”,设置“配料参数”和“时间参数”。
您还可以查看“报警记录”和“记录查询”; 4,进入“操作模式”选择“手动”或“自动”,然后单击“确认”进入操作界面; 5,如果选择“手动”,可以根据工艺要求轻触,需要打开或关闭的机构,红色为关闭状态,绿色为打开状态;设置真空给料机的控制面板。顶部的“进给”和“进给”时间可以通过“开/关”实现;
6.如果选择“自动”,则必须根据工艺要求设置“配料参数”和“时间参数”。当外部设备准备就绪时,按下控制柜上的“配料开始”按钮,然后按“外部准备完成”按钮。系统自动开始运行并在达到设定值后自动停止。
7.混合完成后,控制面板上的电源旋钮开关可以在“关闭”位置关闭。一种
3.自动加料系统说明书备注
1.自动加料系统的送料时间短于送粉时的送料时间,送料时间长于送料时的送料时间。一种或者多种
2.禁止在秤上或附近焊接。 _ 一种或者多种
IV。点检查和操作要求
1.随时观察系统各阀门机构的操作。一种或者多种
2.检查供气压力是否正常,卸料门是否密封以及过滤器是否堵塞。一种或者多种
V.维度,护理和维护
1.定期检查秤的精度,当秤超出公差时需要校准。在维护时应注意固定秤的运动部件。一种或者多种
3.混合后需要清洁真空供料器
Automatic feeding system manual
I. Preparation before starting
1. Check if the air supply pressure of the feeder is normal (0.5-0.6 MPa) and whether the power supply is open; 2. Check whether the pipe fittings are properly connected; 3. Check whether the various materials are ready;
II. Automatic feeding system manual system operation
1. Open the main power switch in the control cabinet, turn the power knob switch on the control panel to the “on” position, and the power indicator light is on;
2. Calibrate and clear the values of the two weighing system monitors under the touch screen;
3. When the touch screen operation enters the function selection screen, you can enter the “parameter setting” according to the process requirements, and set the “batch parameter” and “time parameter”.
You can also view the “Alarm Record” and “Record Query”; 4. Enter “Operation Mode” and select “Manual” or “Auto”, then click “Confirm” to enter the operation interface; 5. If you select “Manual”, you can The process requires light touch, the mechanism that needs to be opened or closed, the red is off, the green is on; the vacuum feeder's control panel is set. The “feed” and “feed” times at the top can be achieved by “on/off”;
6. If you select "Automatic", you must set the "Batch Parameters" and "Time Parameters" according to the process requirements. When the external device is ready, press the “Batch Start” button on the control cabinet and press the “External Ready to Complete” button. The system automatically starts running and stops automatically when the set value is reached.
7. When the mixing is complete, the power knob switch on the control panel can be turned off in the “off” position. One kind
3. Automatic feeding system manual remarks
1. The feeding time of the automatic feeding system is shorter than the feeding time when feeding, and the feeding time is longer than the feeding time when feeding. One or more
2. It is forbidden to weld on or near the scale. _ one or more
IV. Point check and operation requirements
1. Observe the operation of each valve mechanism of the system at any time. One or more
2. Check if the air supply pressure is normal, whether the discharge door is sealed and whether the filter is clogged. One or more
V. Dimensions, care and maintenance
1. Regularly check the accuracy of the scale and calibrate when the scale is out of tolerance. Pay attention to the moving parts of the fixed scale during maintenance. One or more
3. Need to clean the vacuum feeder after mixing
I.启动前的准备工作
1.检查送料器的气源压力是否正常(0.5-0.6 MPa)以及电源是否打开; 2,检查管件是否正确连接; 3,检查各种材料是否准备好;
II。自动加料系统说明书系统操作
1.打开控制柜中的主电源开关,将控制面板上的电源旋钮开关转到“开”位置,电源指示灯亮;
2.在触摸屏下校准和清,除两个称重系统监视器的值;
3.当触摸屏操作进入功能选择屏幕时,可以根据工艺要求进入“参数设置”,设置“配料参数”和“时间参数”。
您还可以查看“报警记录”和“记录查询”; 4,进入“操作模式”选择“手动”或“自动”,然后单击“确认”进入操作界面; 5,如果选择“手动”,可以根据工艺要求轻触,需要打开或关闭的机构,红色为关闭状态,绿色为打开状态;设置真空给料机的控制面板。顶部的“进给”和“进给”时间可以通过“开/关”实现;
6.如果选择“自动”,则必须根据工艺要求设置“配料参数”和“时间参数”。当外部设备准备就绪时,按下控制柜上的“配料开始”按钮,然后按“外部准备完成”按钮。系统自动开始运行并在达到设定值后自动停止。
7.混合完成后,控制面板上的电源旋钮开关可以在“关闭”位置关闭。一种
3.自动加料系统说明书备注
1.自动加料系统的送料时间短于送粉时的送料时间,送料时间长于送料时的送料时间。一种或者多种
2.禁止在秤上或附近焊接。 _ 一种或者多种
IV。点检查和操作要求
1.随时观察系统各阀门机构的操作。一种或者多种
2.检查供气压力是否正常,卸料门是否密封以及过滤器是否堵塞。一种或者多种
V.维度,护理和维护
1.定期检查秤的精度,当秤超出公差时需要校准。在维护时应注意固定秤的运动部件。一种或者多种
3.混合后需要清洁真空供料器
Automatic feeding system manual
I. Preparation before starting
1. Check if the air supply pressure of the feeder is normal (0.5-0.6 MPa) and whether the power supply is open; 2. Check whether the pipe fittings are properly connected; 3. Check whether the various materials are ready;
II. Automatic feeding system manual system operation
1. Open the main power switch in the control cabinet, turn the power knob switch on the control panel to the “on” position, and the power indicator light is on;
2. Calibrate and clear the values of the two weighing system monitors under the touch screen;
3. When the touch screen operation enters the function selection screen, you can enter the “parameter setting” according to the process requirements, and set the “batch parameter” and “time parameter”.
You can also view the “Alarm Record” and “Record Query”; 4. Enter “Operation Mode” and select “Manual” or “Auto”, then click “Confirm” to enter the operation interface; 5. If you select “Manual”, you can The process requires light touch, the mechanism that needs to be opened or closed, the red is off, the green is on; the vacuum feeder's control panel is set. The “feed” and “feed” times at the top can be achieved by “on/off”;
6. If you select "Automatic", you must set the "Batch Parameters" and "Time Parameters" according to the process requirements. When the external device is ready, press the “Batch Start” button on the control cabinet and press the “External Ready to Complete” button. The system automatically starts running and stops automatically when the set value is reached.
7. When the mixing is complete, the power knob switch on the control panel can be turned off in the “off” position. One kind
3. Automatic feeding system manual remarks
1. The feeding time of the automatic feeding system is shorter than the feeding time when feeding, and the feeding time is longer than the feeding time when feeding. One or more
2. It is forbidden to weld on or near the scale. _ one or more
IV. Point check and operation requirements
1. Observe the operation of each valve mechanism of the system at any time. One or more
2. Check if the air supply pressure is normal, whether the discharge door is sealed and whether the filter is clogged. One or more
V. Dimensions, care and maintenance
1. Regularly check the accuracy of the scale and calibrate when the scale is out of tolerance. Pay attention to the moving parts of the fixed scale during maintenance. One or more
3. Need to clean the vacuum feeder after mixing